type   Number   M   o   d   e   l

JBP-P1-20-S

Pump connection port (mm) 
  Pump connection interface

I N-φ25/OUT-φ19

Pump connection pipe 
Pump connection pipe

SuperR300    Sleeve     -insert    Connection

Maximum Flow Rate (L/min) 
Maximum     flow

19 

Pump pressure range (MPaG) 
Pressure range of the pump

When the pump discharge pressure is 0.1 MPaG or higher, the deviation shall be within ±12.5% of the discharge pressure; when the pump discharge pressure is less than 0.1 MPaG, the deviation shall be within 0.03 MPa. 
When the pump discharge pressure is 0.1 MPa gauge pressure (MPaG) or higher, within the range of ±12.5% of the discharge pressure; 
When the pump discharge pressure is less than 0.1 MPa gauge pressure (MPaG), within 0.03 MPa.

Liquid temperature range (°C) 
  Liquid temperature range

10-40

41-70

71-100

Gas Supply Pressure Range (MPaG) 
  Gas Supply Pressure Range

0.2-0.5

0.2-0.4

0.2-0.3

Maximum Discharge Pressure (MPaG) 
Maximum discharge Pressure

0.45 

0.35 

0.25 

Allowable Differential Pressure (MPa) for Pump Bellows 
Allowable differential pressure for pump bellows

0.3 

0.25 

0.2 

Single-stroke displacement 
  Single stroke displacement (L)

0.22 

Air consumption ((Normal)) 
  Air consumption

80-270

Ambient temperature of the pump (°C) 
  Pump ambient temperature

10-50

Gas supply size 
Supply size

Pump drive side 
Pump drive side

2-Rc3/8

Main valve side 
Main valve side

2-Rc1/4

Quality (kg) 
Weight

About 20

1. To achieve the pump’s performance specifications, the piping must be connected using the nominal pipe sizes specified above. In addition, the length of the piping on the pump inlet (IN) side should be limited to no more than 2 meters. 
To achieve the pump’s performance, it is necessary to use piping with the connection caliber specified above. In addition, please ensure that the pipeline run on the pump inlet (IN) side does not exceed 2 meters in length. 
  2. The pump connection ports vary in configuration depending on the type of pipe fitting; therefore, please provide specific instructions on this point when placing your order. 
  3. The allowable differential pressure for the pump’s bellows equals the supply air pressure minus the discharge pressure. 
  4. The values are for reference only. Always operate at a stroke rate of no more than 100 strokes per minute (spm); however, it is recommended to keep the rate below 90 spm. 
These values are reference values. Be sure to operate within 100 strokes per minute (spm); however, the PS-30M must be operated within 90 strokes per minute (spm). 
5. The pump’s external dimensions are for reference only. 
The pump’s outline dimensions are for reference only. 
▲If the fluid being used is an organic liquid or similar and requires explosion-proof treatment, we offer pumps equipped with explosion-proof proximity sensors. Please consult us separately for further details. 
The fluid used is an organic liquid, and explosion-proof treatment is required. Our pumps are equipped with explosion-proof proximity sensors; please consult us separately. 
If the fluid being used is chemical-mechanical polishing (CMP) slurry, we recommend using the “PC Silicone Slurry Pump,” which is specifically designed for CMP slurries. 
If the fluid used is chemical mechanical polishing (CMP) slurry, we recommend the use of a "PC silicone slurry pump" specifically for CMP slurry.

Edit   Number   N   o  .

Name Description

Material

1 

Auxiliary Pump Housing Cover - Damper 
Auxiliary Pump Shell-Damper

Aluminum alloy

2 

Auxiliary Pump Housing - Damper 
Auxiliary Pump Case - Damper

Aluminum alloy

3 

Damping bellows

PTFE

4 

Pump head

PTFE

5 

Import and export port connection 
Inlet and outlet ball joints

PTFE

6 

Base foot

PVC

7 

Valve body

PTFE

8 

Liquid bellows

PTFE

9 

Liquid Bellows Connection Plate 
Liquid bellows connection plate

SUS304

10 

Main Pump Casing - Bellows 
Main pump shell-Bellows

Aluminum alloy

11 

Induction hood

PP

12 

Pump casing cover plate

SUS304

13 

Induction cap

PP